വിദഗ്ധ ഗൈഡ്

സാധാരണ സബ്‌മെർസിബിൾ പമ്പ് പ്രശ്‌നങ്ങളും പരിഹാരങ്ങളും

കുറഞ്ഞ വെള്ളം, ട്രിപ്പിംഗ്, ശബ്ദം, അമിത ചൂടാക്കൽ, വെള്ളം ഇല്ല - പൊതുവായ പ്രശ്നങ്ങൾ കണ്ടെത്തി പരിഹരിക്കുക.

6 മിനിറ്റ് വായന കിംഗ്വെൽ
സാധാരണ സബ്‌മെർസിബിൾ പമ്പ് പ്രശ്‌നങ്ങളും പരിഹാരങ്ങളും

തെറ്റായ ഇൻസ്റ്റാളേഷൻ, ജലനിരപ്പിലെ മാറ്റങ്ങൾ, വൈദ്യുത തകരാറുകൾ അല്ലെങ്കിൽ തെറ്റായ പമ്പ് തിരഞ്ഞെടുക്കൽ എന്നിവയിൽ നിന്നാണ് മിക്ക സബ്‌മെർസിബിൾ പമ്പ് പ്രശ്‌നങ്ങളും ഉണ്ടാകുന്നത്. സേവനത്തിനായി വിളിക്കുന്നതിന് മുമ്പുള്ള സാധാരണ ലക്ഷണങ്ങളും പ്രായോഗിക പരിഹാരങ്ങളും ഈ ഗൈഡിലുണ്ട്.

01

പമ്പ് ആരംഭിക്കുന്നില്ല

Possible causes:

  • No power or tripped MCB — check supply and control panel
  • Low voltage — use stabilizer; motors need rated voltage
  • Cable fault or loose joint — inspect cable from panel to pump
  • Dry run protection activated — verify water level in borewell

Solution: Restore power, fix cable joints, ensure adequate water level, then restart. If motor hums but does not spin, contact authorized service.

02

પંપ ચાલે પણ પાણી ન આવે

Possible causes:

  • Water level dropped below pump intake
  • NRV (non-return valve) stuck or leaking
  • Pipeline leak or air lock in delivery pipe
  • Impeller choked with sand or debris
  • Wrong pump depth setting

Solution: Check water level, inspect NRV and pipes, clean strainer, verify pump is submerged correctly. A complete system inspection restores flow.

03

താഴ്ന്ന മർദ്ദം അല്ലെങ്കിൽ താഴ്ന്ന ഒഴുക്ക്

Possible causes:

  • Partially blocked strainer or pipeline
  • Increased pipe friction from undersized pipe
  • Worn impeller or declining water table
  • Pump operating below rated voltage

Solution: Clean strainer every 3–6 months, verify pipe diameter matches pump capacity, test voltage at panel, and reassess HP if water table has fallen significantly.

04

ഇടയ്ക്കിടെയുള്ള ട്രിപ്പിംഗ് അല്ലെങ്കിൽ ഓവർലോഡ്

Possible causes:

  • Overload relay set too low
  • Single phase failure on three phase supply
  • Mechanical binding or sand ingress
  • Pump oversized for borewell yield (cycling)

Solution: Check all three phases, reset overload correctly, inspect for sand damage, and confirm pump HP matches borewell capacity with your dealer.

05

അസാധാരണമായ ശബ്ദം അല്ലെങ്കിൽ വൈബ്രേഷൻ

Possible causes:

  • Pump hitting borewell wall during installation
  • Loose mounting or worn bearings
  • Cavitation from insufficient submergence
  • Electrical imbalance

Solution: Ensure central alignment in borewell, maintain minimum submergence as per guidelines, schedule dealer inspection for bearing or mechanical wear.

06

കിംഗ്വെൽ എപ്പോൾ സേവനം വിളിക്കണം

Contact your nearest authorized കിംഗ്വെൽ dealer if:

  • Motor burns repeatedly after repair attempts
  • Water flow suddenly stops after years of normal use
  • Warranty repair is needed
  • Pump needs pulling and inspection from borewell

Keep GST invoice and warranty card ready for faster support.

📞ഇപ്പോൾ വിളിക്കുക 💬വാട്ട്‌സ്ആപ്പ് 📋വില നേടുക